skip to Main Content
+90 (506) 158 23 62 info@cestelkimya.com

Moisture Barrier Primer 1000

Moisture Barrier Primer 1000

Description

Moisture Barrier Primer C1000 is a two component, low viscosity, solvent free, epoxy resin.

Advantages

  • Low viscosity
  • Excellent penetration and stabilization of substrate
  • Very good adhesion on the substrate
  • Solvent free
  • Easy roller applied application
  • Shorter construction periods
  • Multiple usage

Application Field

  • Moisture barrier to help control moisture propagation in cementitious substrates with a  moisture content not exceeding 4% by Tramex Method and residual moisture up to 100% R.H.
  • For substrate consolidation on concrete, cement and gypsum screeds.
  • Adhesion promoter for old and new adhesive residues in conjunction with our products.

Storage Shelf life

2 years from date of production if stored properly in undamaged sealed containers at 10 oC and 25 oC.

Technical Data

Density 

A part:  ~ 1.10 kg/l

B part:  ~ 1.02 kg/l

Mechanical / Physical Properties  

Compressive Strength:  ~ 96 N/mm² (7 gün / +23°C / 50% RH)   (EN 196-1)

Adhesion Strength > 1.5 N/mm2 (collapse on concrete)    (EN 4624)

Shore D Hardness     85 (7gün / +23°C / 50% RH)                 (DIN 53505)

How to Use

Coverage: 0.3 – 0.4 kg/m² depend on porosity and substrate surface

  • MUST produce a monolithic, pinhole-free finish with a continuous film. The need for multiple   coats is directly related to surface absorption. Dense substrates can consume less material and   absorbent substrates can consume more material.

Surface Preparation

  • Substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust, and loose   or friable particles. Paint, laitance, and other poorly adhering contents must be mechanically   removed.
  • Substrate must have an open textured surface to allow Primer C1000 to penetrate. (i.e. Blast cleaning, grinding are considered acceptable means to achevie the desired surface profile  but . Acid and chemical etching are not acceptable)
  • At least 50 % of the surface area must be cleared of residual adhesive and cutbacks. (i.e. by grinding or mechanical substrate preparation)
  • Minimum compressive strength > 1160 psi. Tensile Bond strength > 116 psi.
  • The floor must be cleaned with an industrial vacuum prior to installation of the primer C1000.   Consult level/patch system manufacturer regarding priming prior to the placement of materials.
  • Applicator must always verify that preparation of the surface is sufficient prior to using C1000 or patch/level compound.

Conditions/Limits: Substrate temperature during laying and until Primer 1000 has fully cured should be above 10°C and in case of radiant floor heating below 30°C. Application temperature of substrate must be minimum 5°F (3°C) above the measured dew point temperature.

Substrate Humidity: Subfloor moisture content should not exceed 6% when measured with a Tramex moisture meter or 4% when measured using the CM method.

Mixing : Mixing ratio A part:B part=100:50 (by weight). Add one full can of Component B to one full can of Component A then mix with an electric drill and mixing (Jiffy Mixer type) paddle at a low speed to reduce air entrainment (300-400 rpm). A minimum mixing time of 3 minutes shall be observed; mixing shall continue until a homogeneous mix has been achieved. Unmixed material applied to the floor will not cure properly.

Application Conditions

Substrate temperature  Min +10°C / Max +30°C

Environment temperature  Min +10°C / Max +30°C

Substrate Moisture Content

Moisture content by weight < 6%

Equipment Cleaning

Clean all tools and application equipment with cleaning solvent (Xylene, MEK are effective). Hardened/ cured material can only be removed mechanically.

Pot Life

Temperature     Time

+10°C ~ 80 minute

+20°C ~ 50 minute

+30°C ~ 25 minute

Recoating Time solvent free products on Primer C1000;

Substrate Temp Min Max

+10°C 24 hours 4 days

+20°C 12 hours  2 days

+30°C  6 hours 1 day

Above datas that are theoretical, depend on environment temperature, substrate temperature and moisture.

Health and Safety Data

For Further information and advice regarding transportation, handling, storage and disposal of chemical products, user should refer to the actual Safety Data Sheets containing physical, ecological, toxicological and other safety related data.

Cestel Dilatation Tape

It is TPE based with 200 mm wide dilatation tape

Cestel Road Line Paint 

Description

It is an acrylic top coat.It has high chemical resistance like grease and high UV, abrasion resistance.